| https://veliki.com.ua/dir_tricikl_bike_adult.htm |

Начать новую тему Ответить на тему
Автор Сообщение
СообщениеДобавлено: 20.01.2018 23:35 

Сообщения: 21
Город: Родинское
Пол: Муж
Возраст: 33
Зарегистрирован:15.01.2018
сколько масла лить в каждую ногу вилки Manitou SXR ?
или может есть ссылка у кого-то на мануал?
находил за другую вилку мануал так там пишется что масло заливается в миллиметрах по какому-то расчёту.
вот:
The MRD Anti Bob shaft locates the compression piston higher in the
chamber than a normal TPC compression rod, so oil must be added for proper
function of the lockout. Proper oil height can be measured with a simple dip
-
stick, which you can put down into the fork leg. The proper oil height, measured
from the top of the left leg and extending down into the leg, is between 3.75
inches (95mm) and 4.25 inches (108mm). Use Maxima SAE 5-weight oil only
.
W
arning: DO NOTOVERFILLTHE FORK WITH OIL. OVERFILLING
THE FORK COULD CAUSE DAMAGE
TO
THE FORK AND POSSI
-
BL
Y
INJURE THE RIDER.


Вложения:
Комментарий к файлу: Manitou SXR
M9mnwB16IU4.jpg
M9mnwB16IU4.jpg [ 132.65 КБ | Просмотров: 732 ]

Вернуться к началу
shoppage  personalpage P  
 
СообщениеДобавлено: 22.01.2018 21:25 

Сообщения: 43
Город: Харків
Пол: Муж
Возраст: 52
Зарегистрирован:13.06.2017
Гугл в допомогу,тут може тільки якийсь кулібін свої послуги пропонувати...,а краще одразу в велостудію звернутися за сервісом


Вернуться к началу
shoppage  personalpage P  
 
СообщениеДобавлено: 22.01.2018 23:57 

Сообщения: 2609
Изображения: 35
Город: Харьков ХГ
Пол: Муж
Возраст: 39
Зарегистрирован:06.05.2012
люди, люди.........
Мануал уже дали, что даже рассказали и опять здрасте.
Ну неужели тяжело прочитать оглавление того мануала
что дали? открываем читаем.

Цитата:
Chapter8: Damping Assemblies
...........
...........
4. Checking fork oil level
..............


Листаем и находим

Цитата:
Having the correct oil level is critical to keep your TPC fork working at its best.
To measure the oil level, you only need a measuring tape. Begin by unscrewing
the compression valve assembly at the top of the left fork leg. Leave the spring
stack (rider’s right side) installed as it should not be removed to check oil
height.
Once the assembly is completely unthreaded from the inner leg, pull the assembly
about halfway out. You should be able to feel when the piston is no longer
in the fork fluid. When this happens, slowly lower the assembly to where it
again contacts the oil (felt by the increased resistance of the piston in the oil),
and measure the distance from the top of the crown to the top O-ring (located
under the knob above the cap threads). This distance should be approximately
two inches


Ну что непонятного? или еще перевести?

_________________
Gary Fisher Custom


Вернуться к началу
shoppage  personalpage P Персональный альбом  
 
Показать сообщения за:  Поле сортировки  
Начать новую тему Ответить на тему


Вы не можете начинать темы
Вы не можете отвечать на сообщения
Вы не можете редактировать свои сообщения
Вы не можете удалять свои сообщения
Вы не можете добавлять вложения

Найти:
Перейти:  
  © Mishael 2003-2024
Наши друзья: Телеграм-канал про SEO | Рыбалка в Полтаве
Мобильный вид

[ Time : 0.156s | 20 Queries | GZIP : On ]
Reputation System ©'